6063-T5 Equal Aluminum Angle
Lightweight, corrosion-resistant equal-leg aluminum angle for frames, trim, guards and general assemblies. It combines a clean extruded surface with practical cutting, 钻孔, fastening and finishing.
Product Advantages
Two matching nominal leg widths provide simple locating and two mounting faces.
6063 is widely chosen when profile appearance and finish response matter.
The open L-section supports practical framing without the mass of solid bar.
Suitable for many indoor and outdoor applications with correct design.
Suitable for sawing, 钻孔, fastening and qualified aluminum welding.
铣削加工, anodizing and powder coating available subject to quotation.
Chemical Composition · wt.%
Typical 6063 limits are shown below. The applicable purchase standard and material certificate govern the supplied batch.
| 元素 | Limit | 元素 | Limit |
|---|---|---|---|
| Silicon (Si) | 0.20–0.60 | Magnesium (Mg) | 0.45–0.90 |
| Iron (Fe) | ≤0.35 | 铜 (Cu) | ≤0.10 |
| Manganese (Mn) | ≤0.10 | Chromium (Cr) | ≤0.10 |
| Zinc (Zn) | ≤0.10 | Titanium (Ti) | ≤0.10 |
| 其他, 每个 / total | ≤0.05 / ≤0.15 | 铝 (Al) | Balance |
Mechanical and Physical Properties
T5 temper: cooled from an elevated-temperature shaping process, then artificially aged. Values depend on the governing specification and profile thickness.
| Wall thickness | Tensile strength | 0.2% yield strength | Elongation |
|---|---|---|---|
| Up to 12.50 毫米 | 150 MPa min. | 110 MPa min. | 8% min. |
| Over 12.50 to 25.00 毫米 | 145 MPa min. | 105 MPa min. | 8% min. |
| Typical property | 参考值 |
|---|---|
| Density | 大约 2,700 公斤/立方米 |
| 弹性模量 | 大约 69 GPa |
| 导热系数, T5 | 大约 209 带/(m·K) |
| 电导率, T5 | 大约 55% 国际化学学会 |
Reference basis: Hydro 6063 extrusion alloy data. Confirm standard, edition, cross-section and inspection certificate for contractual acceptance.
Equal-Leg Geometry
Specify the section as A × A × t, where A is each nominal leg width and t is wall thickness. Real extrusions include inside and outside corner radii governed by the die and specification. For a closed hollow frame member, see 6063-T5 aluminum square tube; for a solid rectangular mounting blank, compare 6061-T6 aluminum flat bar.
Common Enquiry Sizes
These are common enquiry examples, not a live-stock promise. Typical lengths are 1–6 m or cut to size.
| A × A × t · mm | Approx. mass | Typical use |
|---|---|---|
| 10 × 10 × 1.0 | 0.051 kg/m | Light trim |
| 15 × 15 × 1.5 | 0.115 kg/m | Guards and small frames |
| 20 × 20 × 2.0 | 0.205 kg/m | General framing |
| 25 × 25 × 3.0 | 0.381 kg/m | Cabinets and equipment frames |
| 30 × 30 × 3.0 | 0.462 kg/m | Panels and brackets |
| 40 × 40 × 4.0 | 0.821 kg/m | Medium-duty assemblies |
| 50 × 50 × 5.0 | 1.283 kg/m | Larger frames and supports |
Mass formula: t × (2A − t) × 0.00270 kg/m, with A and t in mm. This sharp-corner estimate excludes radii and tolerances.
Fabrication and Surface Finish
| Process | Ordering guidance |
|---|---|
| Saw cutting | Specify length tolerance, end squareness and deburring. |
| Drilling / fastening | 定义孔位置, edge distance and galvanic isolation. |
| 焊接 | Use a qualified aluminum procedure; heat-affected zones may have lower strength. |
| Anodizing | Specify pretreatment, 厚度, color range and visible-face criteria. |
| Powder coating | Specify preparation, coating system, 颜色, gloss and masking. |
应用领域
Product Presentation and Quality Checks
The image is an AI-generated presentation illustration and does not certify an actual batch, dimension, finish or packing method. Incoming inspection should confirm alloy, 脾气, A × A × t, ordered length, straightness, twist, cut ends, surface condition and documentation.
Packing and Ordering
Long profiles should be supported, separated and bundled to control bending and handling marks. Please provide: 6063-T5; A × A × t; length; 数量; applicable standard; tolerances; straightness and twist limits; cut-end condition; surface finish; packing; and certificate requirements.
Attach drawings for drilled or machined parts. Availability, 最小订购量, processing scope, price and delivery schedule are subject to quotation.
评价
目前还没有评价